Lithium Battery Two Part Potting Adhesive Manufacturer in Ahmedabad, Gujarat, India

INTRODUCTION

Two-component silicone is distinguished and named for the single component silica gel. This product consists of two components and cures after mixing the two components in the right proportion. Generally divided into Condensation type and Addition type, the biggest dierence between the two is Condensation type will release low-molecular substance and Addition type will not, So Condensation type potting will shrink during curing and Addition type potting will not.

APPLICATION

It can use in the high power electronic components, modular power supplies and circuit boards for potting protection,which has good heat conduction and temperature resistance. Such as LED driver power ,automotive HID lamp module power supply, automotive ignition system module power supply, network transformers, etc.

TECHNICAL SPECIFICATION

Two – Component condensation type potting :

Model	Proportion (Weight)	Viscosity-BF (CP)	Color	Viscosity-AF (CP)	Density (g/ml)	Surface Cure Time (Min)	Full Cure Time (H)	Conductivity (W/m-k)	Hardness (Shore A)	Dielectric Strength (kV/mm)
FS-6401	1:1	A: 2600~3400 B: 2600~3400	Gray	2600-3400	1.65±0.02	40-60	2-4	0.9	50–60	≥21
FS-6402	1:1	A: 3500~5000 B: 3500~5000	Gray	3500-5000	2.6±0.02	40-60	2-4	2.0	45–50	≥21
FS-6403	1:1	A: 3800~5000 B: 3800~5000	Gray	3800-5000	2.6±0.02	40-60	2-4	1.5	45–50	≥21
FS-6406	1:1	A: 4500~6000 B: 4500~6000	Grey	4500-6000	2.6±0.02	40-60	2-4	3.0	45–50	≥21

INSTRUCTION

Two-component addition type potting :

Before use, the A component and B component in their respective containers fully mixing evenly, and then according to the weight ratio of A:B=1:1, put into the mixing tank mixing evenly.
Put the mixture into the container. Curing at room temperature or heating. In the winter, it will take a long time to cure, suggested by heating curing, curing under 80 C for 15-30 minutes , and at room temperature, generally takes about 3~5 hours curing

CAUTION

Glue should be sealed storage. The mixture should be used once to avoid waste.
This product is not dangerous, but do not eat and into the eyes.
After a long period of storage, there will be precipitation in the glue. Please mix evenly to use and does not aect the performance.
Glue exposure to a certain amount of the following chemical substances will make the glue does not solidify (little amount of the following substances will not aect the curing)
- N, P, S organic compounds
- Ionic compounds of Sn, Pb, Hg, As and other elements
- Containing alkynes and vinyl compounds
- In order to avoid the above phenomenon the use of the circuit boars as far as possible to wipe clean the remaining rosin, try to use low lead content of solder. It can also use three anti-paint soaked, and then use glue.
Before a large amount of use, please try a small amount of trial to confirm is it appropriate.

PACKING

Two-component addition type potting: 50Kg/ set
Size of 20L Barrel: D30xH38.5cm
Customized special package

STORAGE AND TRASPORT

The storage period see the TDS.
Such products are non hazardous and can be transported in general chemicals

Potting Adhesive Manufcaturer

INTRODUCTION

APPLICATION

TECHNICAL SPECIFICATION

INSTRUCTION

CAUTION

PACKING

STORAGE AND TRASPORT

USING

Quick Links

Our Product

Contact Us